Cisco CCNP BCMSN Exam Tutorial Spanning Tree Protocol STP Timers

MRR and PLR Articles Pack

Below is a MRR and PLR article in category Computers Technology -> subcategory Computer Certification.

Title:
Cisco CCNP / BCMSN Exam Tutorial: Spanning Tree Protocol (STP) Timers

Word Count:
370

Summary:
STP timers are an important part of your CCNP studies and working with STP in real-world networks. Learn the details of these timers and how to change them from Chris Bryant, CCIE #12933.


Keywords:
ccnp, bcmsn, certification, exam, pass, free, stp, spanning, tree, protocol, forward, delay, timer


Article Body:
In your BCMSN / CCNP exam study, it's easy to overlook some of the details of Spanning Tree Protocol (STP). After all, you learned all of that in your CCNA studies, right? Not necessarily! While some of the BCMSN material will be a review for you, there are some details regarding familiar topics that you need to learn. That includes the timers for STP - Hello Time, MaxAge, and Forward Delay.

You may remember these timers from your CCNA studies as well, and you should also remember that these timers should not be changed lightly. What you might not have known is that if you decide to change any and all of these timers, that change must be configured on the root bridge! The root bridge will inform the nonroot switches of the change via BPDUs.

Hello Time is the interval between BPDUs, two seconds by default.

Forward Delay is the length of both the listening and learning STP stages, with a default value of 15 seconds.

Maximum Age, referred to by the switch as MaxAge, is the amount of time a switch will retain a BPDU's contents before discarding it. The default is 20 seconds.

The value of these timers can be changed with the spanning-tree vlan command shown below. Verify the changes with the show spanning-tree command.

SW1(config)#spanning-tree vlan 1 ?

forward-time Set the forward delay for the spanning tree

hello-time Set the hello interval for the spanning tree

max-age Set the max age interval for the spanning tree

priority Set the bridge priority for the spanning tree

root Configure switch as root


SW1(config)#spanning-tree vlan 1 hello-time 5

SW1(config)#spanning-tree vlan 1 max-age 30

SW1(config)#spanning-tree vlan 1 forward-time 20

SW1(config)#^Z

SW1#show spanning-tree vlan 1

VLAN0001

Spanning tree enabled protocol ieee

Root ID Priority 32769

Address 000f.90e1.c240

This bridge is the root

Hello Time 5 sec Max Age 30 sec Forward Delay 20 sec

Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)

Address 000f.90e1.c240

Hello Time 5 sec Max Age 30 sec Forward Delay 20 sec

Aging Time 300

Interface Role Sts Cost Prio.Nbr Type

---------------- ---- --- --------- -------- --------------------------------

Fa0/11 Desg FWD 19 128.11 P2p

Fa0/12 Desg FWD 19 128.12 P2p

Again, you should always take great care in changing these timers. Those defaults are set for a reason - helping to prevent switching loops!




You can find an AI generated version of this article here: Cisco CCNP BCMSN Exam Tutorial Spanning Tree Protocol STP Timers.

You can browse and read all the articles for free. If you want to use them and get PLR and MRR rights, you need to buy the pack. Learn more about this pack of over 100 000 MRR and PLR articles.

“MRR and PLR Article Pack Is Ready For You To Have Your Very Own Article Selling Business. All articles in this pack come with MRR (Master Resale Rights) and PLR (Private Label Rights). Learn more about this pack of over 100 000 MRR and PLR articles.”